意大利瑟肯气体渗氮保护涂料 Thurckon Nit Off Protective Paints
Nit Off 是一款水基型 用于气体渗氮的防渗保护涂料。
Nit Off is a water based nitriding stop-off.
特性/CHARACTERISTICS
灰绿色糊状
Thick grey-green paste
有轻微气味
Slight and pleasant smell
可通过刷涂和浸蘸简单使用
Very easily applicable by brush and immersion
高效的涂层带来均匀渗层
High coating power resulting in perfectly uniform surfaces
可能以任何比例与水混合
Possible to mix with water in all proportions
即使是在不完全脱脂的表面也能有很好的粘附性和保护效果
Very good adhence and protection,even on components not perfectly degreased.
在使用后的很长时间里也不会失去防渗效果或脱落
Nit Off does not deteriorate or flake for long periods after its application
Nit Off是一款防冲击产品
Nit Off is shock resistent
如有必要,干燥后的Nit Off可以手动去除
If necessary,once dried,Nit Off can be manually removed
使用上完全安全
Totally safe to use and to handle
不易燃
Non flammable
Nit Off不需要有机溶剂稀释,水是其唯一的溶剂。当表面的水分完全蒸发后,即可进炉进行热处理加工。
Nit Off does not contain any organic solvents.Water is its only solvent.
干燥后的保护层是不吸湿的
The dried protection is non-hygroscopic
使用/USE
使用前,摇晃并将产品搅拌均匀(可防止由于储存问题而产生的沉淀)
Before use,shake and amalgamate the paste well(it might present a slight deposit at the bottom due to storage)
使用方法/APPLICATION
Nit Off可通过刷涂法和浸蘸使用。
Nit Off can be applied by brush,immersion or spraying.
即使需要防渗的区域没有做到完全的清洁、脱脂,Nit Off也能带来不错的防渗效果。
Even if the parts to be coated should preferably be clean,degreased,non-oxidated and dry,Nit Off gives satisfactory results on not perfectly clean surfaces.
注意:在过于潮湿、油污的表面,Nit Off可能会滑动
Note:on very greasy or very wet surfaces Nit Off tends to run before drying.
刷涂法:
在Nit Off可以使用后,用软毛刷薄涂一层于需要防渗的区域(当涂料过于粘稠时,建议加入2%的清水稀释)
BRUSH APPLICATION:
Spread a thin layer of Nit Off as it is ready to use(dilute with water only if the product appears too viscous due to drying which might result following imperfect storage)
为了更好的涂抹工艺,建议使用软毛刷,避免刷痕。建议涂刷0.2/0.5mm厚度的涂层。
Do not use a stiff brush in order to avoid streaking.The surface of the part to be protected must be coated with a uniform layer about 0.2/0.5mm.
浸蘸:简单的将需要防渗的部位浸入持续搅拌的Nit Off中。
IMMERSION:Simply dip the part into Nit Off,which should be mixed should be mixed in continuation.
干燥/DRYING
在高温环境中干燥大约30分钟
Approximately 30 minutes in a dry and preferably warm environment.
热处理前去除保护层/STRIPPING OF THE PROTECTIVE COMPOUND BEFORE HEAT TREATMENT
Nit Off可以从错误的防渗区域简单地去除,干燥后的涂层可以通过刮刀机械去除。如果需要将涂层完全的从工件表面去除,可以将其浸入水中,Nit Off会以薄膜的形式完整脱落。(干燥后的保护层不再是水溶的,有机溶液是其唯一的溶剂)
Nit Off can easily be removed from erroneously coated areas,the dried coating can be removed mecanically by using a scraper or rasor blade.
热处理后去除表面残留/REMOVAL OF RESIDUES OF HEAT TREATMENT
通过刷子或喷砂可以去除表面的Nit Off残留
For removal of Nit Off residues left on surfaces,brushing or where possible light sand-blasting will suffice.
安全性/SAFETY
本产品对使用者是无害的。根据CEE分类,Nit Off不属于危险品。
The Nit Off components are not harmful to individuals handling them.They are not designated as dangerous according to the CEE classifications.
储存/STORAGE
Nit Off必须要储存在+5℃~+35℃的密封条件下,并且不能在冷藏条件下储存。
Nit Off must be stored at temperatures between +5℃ and +35℃ in well sealed containers and cannot withstand freezing conditions.
Thurckon Srl. 瑟肯防渗涂料 意大利总部: